tooz 47 Posted March 6 hello @wiki11, if you're to use the linux-header 5.10.160 then you will have to use the debian 11 image v.3.0.11 instead of v.3.0.6 Share this post Link to post Share on other sites
wiki11 0 Posted March 6 9 hours ago, tooz said: hello @wiki11, if you're to use the linux-header 5.10.160 then you will have to use the debian 11 image v.3.0.11 instead of v.3.0.6 I use debian 11 image v.3.0.11 and i have problem with install wireguard on this version Share this post Link to post Share on other sites
wiki11 0 Posted March 6 Sorry, my mistake, I write wrong version. I use debian 11 image v.3.0.11 Share this post Link to post Share on other sites
tooz 47 Posted March 7 hello @wiki11, with debian 11 v.3.0.11 install the linux header: sudo dpkg -i linux-headers-5.10.160_5.10.160-1_arm64.deb sudo reboot now install wireguard and the related packages: sudo apt update sudo apt install -y wireguard-dkms wireguard-tool that's all you need to do to get wireguard working -- no need to sudo modprobe Share this post Link to post Share on other sites
wiki11 0 Posted March 7 9 hours ago, tooz said: hello @wiki11, with debian 11 v.3.0.11 install the linux header: sudo dpkg -i linux-headers-5.10.160_5.10.160-1_arm64.deb sudo reboot now install wireguard and the related packages: sudo apt update sudo apt install -y wireguard-dkms wireguard-tool that's all you need to do to get wireguard working -- no need to sudo modprobe When I use command in yours method I see next errors linaro@linaro-alip:~$ sudo apt install wireguard Reading package lists... Done Building dependency tree... Done Reading state information... Done The following packages were automatically installed and are no longer required: liba52-0.7.4 libdca0 Use 'sudo apt autoremove' to remove them. The following additional packages will be installed: linux-image-5.10.0-28-rt-arm64 linux-image-rt-arm64 wireguard-tools Suggested packages: linux-doc-5.10 debian-kernel-handbook Recommended packages: apparmor The following NEW packages will be installed: linux-image-5.10.0-28-rt-arm64 linux-image-rt-arm64 wireguard wireguard-tools 0 upgraded, 4 newly installed, 0 to remove and 64 not upgraded. Need to get 44.8 MB of archives. After this operation, 252 MB of additional disk space will be used. Do you want to continue? [Y/n] Y Get:1 http://deb.debian.org/debian bullseye/main arm64 linux-image-5.10.0-28-rt-arm64 arm64 5.10.209-2 [44.7 MB] Get:2 http://deb.debian.org/debian bullseye/main arm64 linux-image-rt-arm64 arm64 5.10.209-2 [1452 B] Get:3 http://deb.debian.org/debian bullseye/main arm64 wireguard-tools arm64 1.0.20210223-1 [88.9 kB] Get:4 http://deb.debian.org/debian bullseye/main arm64 wireguard all 1.0.20210223-1 [8164 B] Fetched 44.8 MB in 5s (9296 kB/s) Selecting previously unselected package linux-image-5.10.0-28-rt-arm64. (Reading database ... 87219 files and directories currently installed.) Preparing to unpack .../linux-image-5.10.0-28-rt-arm64_5.10.209-2_arm64.deb ... Unpacking linux-image-5.10.0-28-rt-arm64 (5.10.209-2) ... Selecting previously unselected package linux-image-rt-arm64. Preparing to unpack .../linux-image-rt-arm64_5.10.209-2_arm64.deb ... Unpacking linux-image-rt-arm64 (5.10.209-2) ... Selecting previously unselected package wireguard-tools. Preparing to unpack .../wireguard-tools_1.0.20210223-1_arm64.deb ... Unpacking wireguard-tools (1.0.20210223-1) ... Selecting previously unselected package wireguard. Preparing to unpack .../wireguard_1.0.20210223-1_all.deb ... Unpacking wireguard (1.0.20210223-1) ... Setting up linux-image-5.10.0-28-rt-arm64 (5.10.209-2) ... I: /boot/vmlinuz.old is now a symlink to vmlinuz-5.10.0-28-rt-arm64 I: /boot/initrd.img.old is now a symlink to initrd.img-5.10.0-28-rt-arm64 I: /boot/vmlinuz is now a symlink to vmlinuz-5.10.0-28-rt-arm64 I: /boot/initrd.img is now a symlink to initrd.img-5.10.0-28-rt-arm64 /etc/kernel/postinst.d/initramfs-tools: update-initramfs: Generating /boot/initrd.img-5.10.0-28-rt-arm64 raspi-firmware: missing /boot/firmware, did you forget to mount it? run-parts: /etc/initramfs/post-update.d//z50-raspi-firmware exited with return code 1 run-parts: /etc/kernel/postinst.d/initramfs-tools exited with return code 1 dpkg: error processing package linux-image-5.10.0-28-rt-arm64 (--configure): installed linux-image-5.10.0-28-rt-arm64 package post-installation script subprocess returned error exit status 1 Setting up wireguard-tools (1.0.20210223-1) ... wg-quick.target is a disabled or a static unit, not starting it. dpkg: dependency problems prevent configuration of linux-image-rt-arm64: linux-image-rt-arm64 depends on linux-image-5.10.0-28-rt-arm64 (= 5.10.209-2); however: Package linux-image-5.10.0-28-rt-arm64 is not configured yet. dpkg: error processing package linux-image-rt-arm64 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of wireguard: wireguard depends on wireguard-modules (>= 0.0.20191219) | wireguard-dkms (>= 0.0.20200121-2); however: Package wireguard-modules is not installed. Package linux-image-rt-arm64 which provides wireguard-modules is not configured yet. Package wireguard-dkms is not installed. dpkg: error processing package wireguard (--configure): dependency problems - leaving unconfigured Processing triggers for man-db (2.9.4-2) ... Errors were encountered while processing: linux-image-5.10.0-28-rt-arm64 linux-image-rt-arm64 wireguard I need to remove raspi-firmware to be solve that problem? I find on forum that maybe problem with it Share this post Link to post Share on other sites
wiki11 0 Posted March 7 If I remove raspi-firmware and fix install sudo apt install --fix-broken Then I try start wireguard and have next error linaro@linaro-alip:~$ sudo wg-quick up wg0 [#] ip link add wg0 type wireguard Error: Unknown device type. Unable to access interface: Protocol not supported [#] ip link delete dev wg0 Cannot find device "wg0" Share this post Link to post Share on other sites
tooz 47 Posted March 8 hello @wiki11, here's a boot.img with wireguard enabled in kernel config: https://www.asuswebstorage.com/navigate/a/#/s/8C768DB9E19B46FC85A66C56634C40F34 please install the linux-headers-5.10.160_5.10.160-1_arm64 for this version (v.3.0.11) to replace the boot.img: lsblk //to check the partitions if you're using sd card image: sudo dd if=boot.img of=/dev/mmcblk1p4 status=progress && sync sudo reboot for emmc: sudo dd if=boot.img of=/dev/mmcblk0p4 status=progress && sync sudo reboot and then execute sudo wg-quick up wg0 if the .conf is set for wg0 then it should be no errors Share this post Link to post Share on other sites
wiki11 0 Posted March 8 Hello @tooz. I install linux header and install boot.img. I still have errors anymore😓. It is looks like linaro@linaro-alip:~$ sudo wg-quick up wg0 [#] ip link add wg0 type wireguard [#] wg setconf wg0 /dev/fd/63 [#] ip -4 address add 10.6.0.9/24 dev wg0 [#] ip link set mtu 1420 up dev wg0 [#] resolvconf -a tun.wg0 -m 0 -x [#] wg set wg0 fwmark 51820 [#] ip -6 route add ::/0 dev wg0 table 51820 [#] ip -6 rule add not fwmark 51820 table 51820 RTNETLINK answers: Operation not supported [#] resolvconf -d tun.wg0 -f [#] ip link delete dev wg0 Share this post Link to post Share on other sites
wiki11 0 Posted March 8 I am sure in wg0.conf is working, because this config work on my laptop on debian 11 Share this post Link to post Share on other sites
tooz 47 Posted March 11 hello @wiki11, On 3/9/2024 at 4:33 AM, wiki11 said: I still have errors anymore😓. It is looks like i've updated the boot.img with kernel config CONFIG_IP_MULTIPLE_TABLES enabled: https://www.asuswebstorage.com/navigate/a/#/s/8C768DB9E19B46FC85A66C56634C40F34 can you follow the stepts in my previous post to switch the boot.img and see if the error persists? On 3/8/2024 at 5:59 PM, tooz said: to replace the boot.img: lsblk //to check the partitions if you're using sd card image: sudo dd if=boot.img of=/dev/mmcblk1p4 status=progress && sync sudo reboot for emmc: sudo dd if=boot.img of=/dev/mmcblk0p4 status=progress && sync sudo reboot and then execute sudo wg-quick up wg0 Share this post Link to post Share on other sites
wiki11 0 Posted March 11 47 minutes ago, tooz said: hello @wiki11, i've updated the boot.img with kernel config CONFIG_IP_MULTIPLE_TABLES enabled: https://www.asuswebstorage.com/navigate/a/#/MySync/NDI0MzgzMzMwLDgzNDM3Nzg2NSw4MzQzNzc4NjU%3D can you follow the stepts in my previous post to switch the boot.img and see if the error persists? Hello. I check link https://www.asuswebstorage.com/navigate/a/#/MySync/NDI0MzgzMzMwLDgzNDM3Nzg2NSw4MzQzNzc4NjU%3D , but this link leads into personal account, and it is impossible to download file Share this post Link to post Share on other sites
tooz 47 Posted March 11 hello @wiki11, this link should work: https://www.asuswebstorage.com/navigate/a/#/s/8C768DB9E19B46FC85A66C56634C40F34 Share this post Link to post Share on other sites
wiki11 0 Posted March 11 1 hour ago, tooz said: hello @wiki11, this link should work: https://www.asuswebstorage.com/navigate/a/#/s/8C768DB9E19B46FC85A66C56634C40F34 Now wireguard work. Thank you so mush. Little instruction for install wireguard on version debian 11 image v.3.0.11 looks like that 1) Install image on sd card 2) increase part /dev/mmcblk1p7, if you want update kernel 3) Download from link linux header and boot 4) sudo dpkg -i linux-headers-5.10.160_5.10.160-1_arm64.deb sudo reboot now 5) if you're using sd card image: sudo dd if=boot.img of=/dev/mmcblk1p4 status=progress && sync sudo reboot for emmc: sudo dd if=boot.img of=/dev/mmcblk0p4 status=progress && sync sudo reboot 6) sudo dpkg --purge raspi-firmware sudo reboot 7) sudo apt-get update sudo apt install wireguard Share this post Link to post Share on other sites
tooz 47 Posted March 11 hello @wiki11, good to know it works and thank you for the instruction Share this post Link to post Share on other sites
