26.albertsilva@gmail.com
-
Content Count
8 -
Joined
-
Last visited
Posts posted by 26.albertsilva@gmail.com
-
-
Estamos probando el Tinkerboard 3N en el siguiente escenario:
Tinkerboard 3N instalado con debian 11, arrancando desde micro-SD
-
Debemos conectar dos pantallas al tinkerboard 3N. Ambas pantallas deben funcionar como pantallas extendidas (no reflejadas)
- La pantalla principal está conectada al puerto HDMI de la pizarra (resolución actual 1024x600)
- La pantalla secundaria se conecta al conector eDP interno de la pizarra mediante un cable eDP - DP personalizado. El monitor secundario es un monitor HP estándar (resolución actual de 1920x1080), solo para fines de prueba.
-
El resultado de esta prueba es que no se detecta el monitor secundario.
- No se crea card1-EDP-1 en /sys/class/drm, solo podemos ver card0-HDMI-A-1 (HDMI funciona)
- xrandr -q solo emite HDMI-1 como conectado, no se muestra información sobre DP-1
-
Modificación realizada
-
Cambiamos algunas variables en el entorno u-boot, pero sin éxito. Mismo resultado que el indicado en el punto 3.
- setenv display0 hdmi-default
- Setenv Pantalla1 EDP-1920x1080
- setenv display2
- saveenv
-
Otros cambios
- setenv display0 hdmi-default
- Setenv Pantalla1 EDP-1024x600
- setenv display2
- saveenv
-
Cambiamos algunas variables en el entorno u-boot, pero sin éxito. Mismo resultado que el indicado en el punto 3.
-
Otras pruebas que hemos realizado cambiando vars en el entorno uboot, pero los mismos resultados HDMI funciona y EDP no funciona
-
Resoluciones predeterminadas
- setenv display0 hdmi-default
- Setenv Pantalla1 EDP-1366x768
-
setenv display2
-
saveenvsolo una interfaz (eDP)
- Setenv Pantalla0 EDP-1366x768
- setenv display1
- setenv display2
- saveenv
-
saveenvsolo una interfaz (eDP)
-
Resoluciones predeterminadas
-
Observaciones
- Creemos que el kernel debe detectar el DP-1, esperamos detectar en /sys/class/card1-DP-A-1 o dispositivo similar la pantalla secundaria
- ¿El kernel necesita alguna cmdline para configurar la pantalla secundaria?
- ¿Se debe agregar o habilitar algún módulo nuevo en la configuración del kernel?
---------------
Se está evaluando con un monitor secundario es un monitor HP estándar (resolución actual de 1920x1080), solo con fines de prueba.
¿Puede compartir un adaptador de cable pasivo eDP1.3 a DP esquemático recomendado por ASUS que funcione con Tinker 3N y un monitor HP estándar con entrada DP?
Señal eDP en el cabezal de 40 pines:
Señal de pin del conector DP:
Gracias de antemano por su apoyo.
Saludos
cordiales Albert Silva -
Debemos conectar dos pantallas al tinkerboard 3N. Ambas pantallas deben funcionar como pantallas extendidas (no reflejadas)
-
Hi
I said LVDS because the same connector is used for dual LVDS and eDP but, the secondary monitor is connected to the eDP port, the primary is connected to the HDMI port. We set the uboot vars for display0 and display1 as follows
setenv display0 hdmi-default
setenv display1 edp-1366x768
setenv display2
saveenv
reset
But the DP monitor is not working and in /sys/class/drm only one card is showed the hdmi one. Do we need configuring the kernel, modify dtb ..etc?
Regards
-
Hello
I would like to use two monitors to enlarge the screen.
I connected one monitor to the HDMI interface and the other to the LVDS port, I only see the HDMI signal the LVDS I don't see it, and with xrandr I only see HDMI-1 I don't see the other output.
-Is there any way to enable it, how can I get to that?
At the moment, the image "Tinker_Board_3N-Debian-Bullseye-v1.0.7-20230828-release" is running, but I am open to use another one if necessary.
I look forward to your prompt reply.
Thank you.
-
I've already been able to access, ok now my query is how do I enable the LVDS output for a second display? in /proc/sys/class I only see HDMI
-
We're connecting to these pins
-
I'm connected to the dbug port, on the 3-pin board, we think it's that one, I'm not sure, I've enabled the UART from the tinker-config but I'm also not sure if they're the right ones. In addition to this, the parameters that must be configured in the standard 11, in the fw_env.config file for the fw_printenv utilities to work, and set_printenv to be able to access via Linux in case of not being able to get the serial connection.
-
Hello
How do I enable the serial console on tinker board 3N?
I'm running TinkerOS Debian 11, I'm trying to enable LVDS output on the uboot without success. Any suggestions?
(URG) How to enable serial console on tinker board 3N?
in General Discussion
Posted
Hi
to give you more context on what we are doing. We are testing the Tinkerboard 3N in the following scenary:
---------------
Customer is evaluating with a secondary monitor is a standard HP monitor (current resolution 1920x1080), just for testing purposes.
can you share a passive cable adapter eDP1.3 to DP schematic recommended by ASUS that work with Tinker 3N and a standard HP monitor with DP input?
eDP signal on header 40pin.:
DP connector pin signal:
Thank you in advance for your support.
Best regards