Jump to content

Search the Community

Showing results for tags 'uboot'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • General
    • Announcements
  • Tinker Board 3N
    • General Discussion
    • Hardware
    • Software
  • Tinker Board 3 Series
    • General Discussion
    • Hardware
    • Software
    • Android
  • Tinker V
    • General Discussion
  • Tinker Board 2 series
    • General Discussion
    • Hardware
    • Software
    • Android
  • Tinker Board / Tinker Board R2.0 series
    • General Discussion
    • Hardware
    • Software
    • Android
  • Tinker Edge T
    • General Discussion
    • Hardware
    • Software
  • Tinker Edge R
    • General Discussion
    • Hardware
    • Software
    • Android

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 2 results

  1. Hello How do I enable the serial console on tinker board 3N? I'm running TinkerOS Debian 11, I'm trying to enable LVDS output on the uboot without success. Any suggestions?
  2. Hi everybody, Recently, I have been trying to run some bare metal code on my Tinker Board 2. I managed to compile ARM Trusted Firmware - A successfully with these commands: % git clone https://github.com/ARM-software/arm-trusted-firmware.git tf-a % cd tf-a % export CROSS_COMPILE=~/Developer/Toolchains/aarch64-none-elf/bin/aarch64-none-elf- % make PLAT=rk3399 After that, I tried to build U-Boot with these commands (the CROSS_COMPILE variable is set from previous commands): % git clone https://github.com/TinkerBoard2/u-boot.git uboot % cd uboot % export BL31=../tf-a/build/rk3399/release/bl31/bl31.elf % export KBUILD_OUTPUT=build % make tinker2_defconfig % make This, unfortunately failed with this error: DTC arch/arm/dts/rk3036-sdk.dtb Error: arch/arm/dts/.rk3036-sdk.dtb.pre.tmp:77.1-10 syntax error FATAL ERROR: Unable to parse input tree I tried to fix the problem, and I thought removing 'rk3036-sdk.dtb' from 'arch/arm/dts/Makefile' could work since it seemed to be the device tree of another board that I was building for, which happened to be ill formed. That made the problem disappear, but the same thing happened for 'rk3368-lion.dtb', 'rk3368-sheep.dtb' and a couple of other device trees. I removed them all (7 in total) and the build finally succeeded. I then created a GPT disk image, with a single FAT32 partition with my code compiled, in it. The partition started at sector 18405, so there should have been plenty space for U-Boot. I verified with gdisk that my disk image is not corrupt, so that is clearly not the problem. I tried writing U-Boot into the SD card with the instructions in https://github.com/u-boot/u-boot/blob/master/doc/README.rockchip and https://github.com/u-boot/u-boot/blob/master/doc/board/rockchip/rockchip.rst. Packaging with rockchip miniloader did kind of work, but it printed some unusual characters (Chinese or Japanese?) and a lot of diamonds with single question mark in them at the beginning, and I had to set the baud rate to 120000 to view the output properly. Using U-Boot SPL and U-Boot TPL + SPL only printed one diamond with a question mark in it. I also tried the method provided as an answer to this post, but that did not work, probably because it was for eMMC. I used this command to see if it worked: minicom -D /dev/cu.usbserial-1440 -b 115200 -o I connected my serial to USB cable as instructed in this post I am sure my board is not broken as I was able to run the official Debian image without U-Boot printing any weird characters or problems with baud rate. I wonder, if any Tinker Board engineers could share how U-Boot is built when preparing the official image. Any help is appreciated.
×
×
  • Create New...