Jump to content

Kubo

Members
  • Content Count

    7
  • Joined

  • Last visited

Everything posted by Kubo

  1. Hello, @qwuke I flashed the new os to tinker edge r with the following steps 1. Flash the os [Tinker Edge R Debian Stretch V1.0.4 2020/07/07] to tinker edge r. [Tinker Edge R Debian Stretch V1.0.4] older than 2020/07/07 may not be possible transition to ums mode. I recommend download [Tinker Edge R Debian Stretch V1.0.4] again. 2. Start LXterminal on tinker edge r and connect USB Type-C 3. run the following command on LXterminal sudo reboot ums 3. If you are asked to format the drive on your computer, it is a success. 4. Start Etcher on PC and flash new os.
  2. I was able to flash "Tinker Edge R Debian Stretch V1.0.13" to "Tinker Edge R" and launch it! →I can now flash "Tinker Edge R Debian Stretch V1.0.13" to "Tinker Edge R" and boot!!
  3. Thank you @tooz I was able to flash "Tinker Edge R Debian Stretch V1.0.13" to "Tinker Edge R" and launch it! In UMS mode, it was "Linux UMS disk 0 USB Device" instead of "ASUS Tinker UMS USB Device", but there was no problem. Value in the image : USBSTOR\DISK&VEN_LINUX&PROD_UMS_DISK_0&REV_FFFF\28EBEC221ABCEF32&0 Finally, do you know why you couldn't flash "Tinker Edge R Debian Stretch V1.0.13" to Tinker Edge R using "Tinker_Edge_R-Flash_GUI_V1.0.0"? (Is there something missing in my computer environment?) I will set up more than a dozen more units, so I would like to know if there is a way to set up efficiently. thanks
  4. Hi @tooz The PID & VID of the driver looks like the image.
  5. @tooz I can start the boat with the current image(Tinker Edge R Debian Stretch V1.0.4). I downloaded the image(Tinker Edge R Debian Stretch V1.0.4 and V1.0.13) from the official website. Here is an image of the Etcher on my computer. ASUS Tinker UMS USB Device does not appear in [Select target]. (C drive and D drive appear). Here is an image of Device Manager. The device(Tinker Edge R) is recognized as "Tinker Edge R" in "Universal Serial Bus Devices" instead of "ASUS Tinker UMS USB Device" in "Desk Drive". Other, I tried it with a new Tinker Edge R and a Tinker Edge R with android os installed, but I couldn't.
  6. hello @tooz I connected to Tinker Edge R and PC using USB Type-C and started PC and Tinker Edge R, but Tinker Edge R option does not appear on balenaEtcher. But Device Manager recognizes Tinker Edge R as one of the Universal Serial Bus Controller. And I don't know UMS mode, is the correct way to boot in UMS mode by booting without shorting the recovery header?
  7. Hello I tried to flash Tinker Edge R Debian Stretch V1.0.13 to the Tinker Edge R as per the official documentation, but it failed to load the firmware and I can't flash. V1.0.4 succeeds, but V1.0.13 fails. I tried using Tinker_Edge_R-Flash_GUI_V1.0.0, AndroidTool, RKDevTool and flash.cmd. Please tell me how to deal with this problem. Rockchip_DriverAssitant Version 5.1.1 Tinker_Edge_R-Flash_GUI_V1.0.0 Flash failed (Please Power off the device, ...) AndroidTool_Release_v2.51 or RKDevTool (Ver.2.81) Loading firmware failed! flash.cmd Loading firmware... Loading firmware failed! Press any key to exit... Also, there was no problem in checking SHA256 of Tinker Edge R Debian Stretch V1.0.13 zip. thanks
×
×
  • Create New...